[Cryptech-Commits] [core/coretest] 01/01: Adding license and readme file.
git at cryptech.is
git at cryptech.is
Thu Mar 13 14:22:31 UTC 2014
This is an automated email from the git hooks/post-receive script.
joachim at secworks.se pushed a commit to branch master
in repository core/coretest.
commit 55fbc54c20630a089b991cc53481aa8f0f268494
Author: Joachim Strömbergson <joachim at secworks.se>
Date: Thu Mar 13 15:22:26 2014 +0100
Adding license and readme file.
---
LICENSE | 24 +++++++++
README.md | 176 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
2 files changed, 200 insertions(+)
diff --git a/LICENSE b/LICENSE
new file mode 100644
index 0000000..9a95faa
--- /dev/null
+++ b/LICENSE
@@ -0,0 +1,24 @@
+Copyright (c) 2014, SUNET
+Joachim Strömbergson
+All rights reserved.
+
+Redistribution and use in source and binary forms, with or without modification,
+are permitted provided that the following conditions are met:
+
+* Redistributions of source code must retain the above copyright notice, this
+ list of conditions and the following disclaimer.
+
+* Redistributions in binary form must reproduce the above copyright notice, this
+ list of conditions and the following disclaimer in the documentation and/or
+ other materials provided with the distribution.
+
+THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
+ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR
+ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
diff --git a/README.md b/README.md
new file mode 100644
index 0000000..2c38361
--- /dev/null
+++ b/README.md
@@ -0,0 +1,176 @@
+# coretest #
+Test platform for the [Cryptech Open HSM project](https://cryptech.is/).
+
+(_Note:The Cryptech certificate is by choice not from a CA and therefore
+not in your brower trust store._)
+
+
+## Description ##
+This platform and hardware design is used to functionally verfiy cores
+developed in the Cryptech Open HSM project. The test core itself
+contains just enough functionality to be able to verify that the SW in
+the host computer can talk to the core in the FPGA by reading and
+writing 32 bit data words to given addresses.
+
+This project includes cores in Verilog, a testbench as well as host SW
+to talk to the core.
+
+
+## Architecture ##
+The coretest consists of three state machines:
+
+### rx_engine ###
+Handles receiving command messages from the host. Awaits SYN signals from
+the host interface and reads bytes when SYN is asserted. For each byte
+the rx_engine assetts and ACK and waits for the SYN to be asserted. When
+a EOC byte has been detected the rx_engine signals the test_engine that
+there is a new command available in the rx_buffer.
+
+
+### tx_engine ###
+Handles transmitting response messages to the host. When the test_engine
+signals that there is a new response in the tx_buffer the tx_engine will
+start transmitting all bytes up to and including the EOR byte it is
+expecting in the tx_buffer. The transmission is done by asserting SYN
+awaiting ACK, deasserting SYN and moving to the next byte before
+asserting SYN again. This process is repeated until all bytes has been
+transmitted.
+
+
+### test_engine ###
+Performs the parsing of commands from the host. Known read or write
+commands are used to test the core to be tested. The response from the
+core is collected and the appropriate response is stored in the
+tx_buffer. The test_engine then signals the tx_engine that there is a
+new response message to be transmitted.
+
+## Interfaces ##
+The host communication interface is a byte wide data interface with
+SYN-ACK handshake for each byte.
+
+The interface to the core to be tested is a memory like
+interface with chip select and write enable. The data width is 32-bits
+and the address is 16-bits.
+
+
+## Core under test ##
+The core under test is expected to have a simple memory like interface
+with chip select (cs), write enable (we) signal ports, 16-bit address
+port and separate 32-bit data ports for read and write data. The core is
+also expected to have an error signal port that informs the master if
+any read or write commands given cannot be performed by the core.
+
+***Note:***
+The core reset signal is expected to by active high. The
+core reset signal should be connected to the coretest core_reset
+port, not to system reset.
+
+
+## Protocol ##
+Coretest uses a simple command-response protocol to allow a host to
+control the test functionality.
+
+The command messages are sent as a sequence of bytes with a command byte
+followed by zero or more arguments. The response consists of a response
+code byte followed by zero or more data fields.
+
+The start of a command is signalled by a Start of Command (SOC)
+byte. The end of a command is signalled by a End of Command (EOC)
+byte. These bytes are:
+ - SOC: 0x55
+ - EOC: 0xaa
+
+The start of a response is signalled by a Start of Response (SOR)
+byte. The end of a response is signalled by a End of Respons (EOC)
+byte. These bytes are:
+ - SOR: 0xaa
+ - EOR: 0x55
+
+***The commands accepted are:***
+ - RESET_CMD. Reset the core being tested. Message length is 3 bytes
+ including SOC and EOC.
+ - SOC
+ - 0x01 opcode
+ - EOC
+
+
+ - READ_CMD. Read a 32-bit data word from a given address. Message
+ length is 5 bytes including SOC and EOC.
+ - SOC
+ - 0x10 opcode
+ - 16-bit address in MSB format
+ - EOC
+
+
+ - WRITE_CMD. Write a given data word to a given address. Message
+ length is 9 bytes including SOC and EOC.
+ - SOC
+ - 0x11 opcode
+ - 16-bit address in MSB format
+ - 32-bit data in MSB format
+ - EOC
+
+
+***The possible responses are:***
+ - UNKNOWN. Unknown command received. Message length is 4 bytes
+ including SOR and EOR.
+ - SOR
+ - 0xfe response code
+ - Received command
+ - EOR
+
+
+ - ERROR. Known but unsuccessful command as signalled by the
+ core. Caused for example by a write command to read only
+ register. Message length is 4 bytes including SOR and EOR.
+ - SOR
+ - 0xfd response code
+ - command received
+ - EOR
+
+
+ - READ_OK. Sent after successful read operation. Message length is 9
+ bytes including SOR and EOR .
+ - SOR
+ - 0x7f response code
+ - 16-bit address in MSB format
+ - 32-bit data in MSB format
+ - EOR
+
+
+ - WRITE_OK. Sent after successful write operation. Message length is 5
+ bytes including SOR and EOR
+ - SOR
+ - 0x7e response code
+ - 16-bit address in MSB format
+ - EOR
+
+
+ - RESET_OK. Sent after successful reset operation. Message length is 3
+ bytes including SOR and EOR.
+ - SOR
+ - 0x7d response code
+ - EOR
+
+## Status ##
+***(2014-02-11):***
+
+Added information about the architecture and protocols. Updated the
+command and response with explicit read and write ok responses. Some
+cleanup of the description.
+
+Completed first draft of the RTL for coretest. The RTL is not debugged
+and has not been synthesized. We need to add a testbench and a simple
+test core.
+
+Added a simple test core.
+Adding initial version of UART core that will be used for the host
+interface.
+
+
+***(2014-02-10):***
+
+Initial version of the project. Based on previous cttest project but
+renamed and with new (ideas) about the test architecture. Specified
+command and response protocol.
+
More information about the Commits
mailing list